A drill press chuck is one of essential elements of a drill press. As it is one of the important parts which involves in drilling and contacting the hard surface directly, you need to have a quality of this item. This article will guide the reader with important information on drill press chuck. It also will guide you how to clean the chuck and remove it securely from the drill presses.
The chuck of a drill press needs to be cleaned regularly to have precise and proper cuts on the surface of the items. The chuck helps you to have accurate drilling along with having precise leveling for drilling holes.
What is a Drill Press Chuck?
The clamp with jaws of the drill press is there to tight fit the drill bit. Normally, a chuck is made with three jaws clamp. These jaws tighten the drill bit along with securely covering the shank of the bits. The chuck is constructed with a wrench. This geared wrench is known as a chuck key.
Drill Press Chuck Sizes
Drill press chuck can have a size of ½ inches for most drill presses. It can have a size of ¾ inches as well for some chucks. There are different companies providing best kinds of drill presses with various drill press chuck sizes.
How to Install a Drill Bit?
To install a bit, you have to insert the shank into the chuck and tighten the collar. It will eventually secure the bit with a firm hold. Then you need to insert the tip of the chuck key in the hole. Then you need to make an align of the gears to set it properly.
Just make sure you simply insert the shank of into the chuck and tighten the collar with hands. Then, till the jaws consistently hold the bit,insert the tip of the chuck key into holes.
Removing Drill Press Chuck
When we talk about cleaning the chuck of a drill press, we actually suggest about the part that holds the drill bits. Removing a drill press chuck is very easy if you know the method properly. However, there are more than one ways to do it. Most of these methods do not take times and very easy to operate.
Using Drill Press Chuck Removal Tool
Using chuck removal tool is one of the most used methods for removing chuck easily. Most of the DPs come with a tool for removing chuck. This tool is known as the chuck removal tool. Using this tool, you can remove the chuck in a very quick and easy way.
You just need to Insert the tool into the window of the spindle of the drill press. This will be a very easy way. Then you have to hammer the chuck removal tool lightly into the window of the DP until the chucks fall from the press. You need to do it precisely and using the weight lightly.
[responsive_video type=’youtube’ hide_related=’1′ hide_logo=’0′ hide_controls=’0′ hide_title=’0′ hide_fullscreen=’0′ autoplay=’0′]https://www.youtube.com/watch?v=KbI_7IHAsyw[/responsive_video]
Just raised the table a little up or hold something in the falling areas of the chuck. So the chuck will not be damaged during falling off the press.
Hammer and Hardwood Method
Sometimes, you may not find the chuck removal tool in between your reach. But if you need to clean it immediately then learning other methods can really be useful. You can use a hammer with a piece of harder wood to do it easily. Although, it may not be as easy as using the drill press chuck removal tool.
If you can use a hard wood piece along with the hammer, it will also be a safer method. You just need to position the hard piece of wood above the chuck with having an angle. Setting an angle will not be a tough work as you already know where it should hit.
Then, you just have to whack the hardwood using the hammer. Just give it two or three so that the chuck come out of the drill press. You just need to keep an eye on the hammer; it doesn’t harm your hand. Also, make sure the hammer whack with a down angle. So, the chuck shaft will not bend.
Cleaning the Chuck
Before reinstalling the chuck, you need to clean it properly. So, it will get back to its working condition smoothly without having any trouble. Chucks have tight, “Morse taper” fitting. So, it can composite any oil, debris or dirt on the shaft that will hold of the chuck in the press.
You can clean the chuck after removal with the decreasing agent using a rag. Liquids like Acetone will work fine for the cleaning process because of its quick evaporation facility. You clean the chuck very quickly, and within moments it will be fine for using again.
Reinstalling The Drill Press Chuck
Insert the chuck into the drill press after the spindle and chuck get clean. Do this process firmly as it will stay in the press for a moment. Then you have to retract the drill press jaws quickly. You will get used to it easily after doing it for two or three times.
After doing the previous process, you need to keep the chuck in its place. So, you need to place the table little lower to create space for hammer swing. Then, strike the bottom of the chuck quickly with the hammer two or three times.
[responsive_video type=’youtube’ hide_related=’1′ hide_logo=’1′ hide_controls=’0′ hide_title=’0′ hide_fullscreen=’0′ autoplay=’0′]https://www.youtube.com/watch?v=VnXGy_-SAGk[/responsive_video]
There are some other methods and tools like removing the chuck with using chuck removal wedges. Well, you can easily find the chuck removal wedges on the marketplace. But the provided methods of removing chuck are our favorite one.
If you follow the steps in removing and reinstalling the chuck properly, it will get very easy with times. Just make sure, you do the process safely and attentively so that that doesn’t create any risk factors.